The winner is the air that is easier to install and it looks like it burns less. About 2DL per hour during the test operation. Type the AIRTOP 2000ST, capable of 2KW and currently has an internal thermostat. Actuated by the switch or on a special thermostat. Since I do not have a thermostat, I prožl with the switch. This means operating at full. Therefore, I added a thermostat on the output, which will izklapljal if the temperature exceeds the desired value.
During buffet food warmers the test, it turned out that the case for the operation of the switch needs an LED in series with a switch. This LED, I chose green, gives an indication of operation and in the event of a failure communicating with blinkanjam. Other LED'm after several attempts with different resistors fitted at random on the other two contacts the trigger line and the case starts. For this indication, I chose the red LED. Obviously, it is necessary to detect the voltage drop in the liniju and then ASTARTA.
I installed it under the center console buffet food warmers that blows in the front passenger side. So far it has proved to be an excellent heating. The air is warm without gas and emits no noise, except at the start. Sounds just a fan. In operation, buffet food warmers devouring approximately 10A 12VDC, which sees the car as app 1A of batteries :).
EDIT: The system works well. Potrrebno is installing warm air in the ventilation tube that can be directed warm air throughout the room. I have also noted that the switch on the rear window is not a particularly good idea. The switch is connected to the ECU unit, which activates a timer and after a 15minute buffet food warmers disconnected heater. This is done to protect the coils rear window. Menu in the middle of driving off webasto !!! I had to refer the matter to binding to a separate switch. It is easy to go on the left side of the steering wheel, where he was free bracket for the switch. That's where I edited the switch and two LEDs. Now we show excellent buffet food warmers operation Webasta.
I made a tank made of sheet metal. Hang around 4,5L and I assume that will be enough for the weekly drive to work. I montilral it also holds for the pump. Output pin I made on the lathe from the M10 bolt and welded to the side. The neck and cap also on a lathe from 30mm pipe and plastic. I installed a tank in the trunk behind where the room was perfect for that. I spent some time thinking about how to fasten. In the end, I just sit with mounting Purp. Now hold fixed and there is no reason to rip. The last detail was the vent hole in the cap of the fuel. Due to the negative buffet food warmers pressure in the cap, I drilled a 0.8mm hole to equalize the pressure in the tank.
You are commenting buffet food warmers using your Twitter account. (Log Out / Change)
Recent posts ENGINE COOLING BMS logging RPM indicator indicator for fuel 3f Processing charger adapter charger into three phases 400VAC 10.000Km! Webasto! Reducing the charger Archive June 2014 (2) May 2014 (2) April 2014 (1) March 2014 (1) January 2014 (1) December buffet food warmers 2013 (2) November 2013 (2) October 2013 (1) August 2013 (1) June 2013 (3) May 2013 (1) April 2013 (3) March 2013 (4) February 2013 (2) January 2013 (2) December 2012 (6) November 2012 (7) October 2012 (5) September 2012 (8) August 2012 (4) July 2012 (11) June 2012 (1) May 2012 (10) April 2012 (7) March 2012 (7) Categories LOG (87) MAZDA (5) RECOVERY (78) TEST (23) Preparation (11) Search Search for: Tags
Adapter plate 12v battery BMS electric car EV Gas pedal heating approval instrument panel exhaust system components buffet food warmers construction contactors controller Mazda MX3 engine gearbox wiring Engine mount the drive covers charger relay processing tank seats clutch vacuum system fuse Video flywheel brake steering box
% D bloggers like this:
No comments:
Post a Comment